^  location  ^  size  ^  pitch  ^  thread length\\ (shoulder length)  ^  more details  ^  years  ^
^  Engine  ^^^^^^
|  upper rear timing cover  |  M6  |  1.0  |  10mm  (none)  |  bolt + split washer  |  all  |
|  distributor bracket  |  M6  |  1.0  |  20mm (none)  |  bolt  |  all  |
|  distributor cap  |  M4  |  0.75  |  25mm (none)  |  bolt  |  all  |
|  harmonic balancer to crank  |  M10  |  1.0  |  120mm  |  bolt + flat washer  |  84-87  |
|  harmonic balancer to crank  |  M12  |  1.25  |  ?  |  bolt + flat washer  |  88-89  |
|  pulleys to harmonic balancer  |  M6  |  1.0  |  15mm  |  bolt + split washer  |  all  |
|  timing belt tensioner  |  M10  |  1.25  | |  nut + flat washer  |  all  |
|  CHTS  |  M12  |  1.25  | ||  all  |
^  Engine (accessories)  ^^^^^^
|  alternator bracket to block  |  M10  |  1.5  |  60mm  |  bolt + split washer  |  87-89  |
|  alternator adjuster to block  |  M8  |  1.25  |  25mm (40mm)  |  bolt + split + flat washer  |  all  |
|  alternator to bracket  |  M8  |  1.25  |  20mm  |  bolt  |  all  |
|  air conditioner bracket to block  |  M10  |  1.5  |  25mm (20mm)  |  bolt  |  all  |
|  air conditioner bracket to block  |  M8  |  1.25  |  25mm (90mm)  |  bolt  |  all  |
|  upper p/s pump bracket  |  M8  |  1.25  |  35mm  |  bolt + split washer  |  all  |
|  lower p/s pump bracket  |  M10  |  1.5  |  20mm  |  bolt + flat washer  |  84-86  |
|  front-right hoist bracket  |  M8  |  1.25  |  50mm  |  bolt + split washer  |  all  |
|  front-right hoist bracket  |  M8  |  1.25  |  16mm  |  bolt + split washer  |  all  |
|  motor mount bracket to block  |  M10  |  1.5  |  20mm  |  bolt + split washer  |  all  |
|  motor mount stabilizer to bracket  |  M10  |  1.5  |  25mm  |  bolt + split washer  |  all  |
|  motor mount stabilizer to block  |  M10  |  1.5  |  20mm  |  bolt + split washer  |  all  |
^  Engine (cooling)  ^^^^^^
|  filler neck  |  M8  |  1.25  |  50mm (?)  |  bolt + split + flat washer  |  all  |
|  t-stat housing  |  M8  |  1.25  |  72mm (?)  |  bolt + split + flat washer  |  all  |
|  t-stat housing cover  |  M8  |  1.25  |  34mm  |  bolt + split + flat washer  |  all  |
|  water pump pulley  |  M6  |  1.0  |    |  stud + split washer + nut  |  all  |
|  filler neck to heater tube flange  |  M6  |  1.0  |  18mm (none)  |  bolt + split washer  |  all  |
|  heater tube front+rear flange  |  M6  |  1.0  |  18mm (none)  |  bolt + split washer  |  all  |
|  heater tube hold-down  |  M6  |  1.0  |  14mm (none)  |  bolt + split washer  |  all  |
^  Engine (lubrication)  ^^^^^^
|  oil pump  |  M6  |  1.0  |  20mm  |  bolt + split washer  |  all  |
|    |  M6  |  1.0  |  30mm  |  bolt + split washer  |  all  |
|  oil pan  |  M6  |  1.0  |  14mm (none)  |  bolt + split washer  |  all  |
|  oil temp sensor bung  |  M16  |  1.5  |    |    |  all (turbo)  |
|  oil sender port  |  1/8"  |  BSPT  |    |    |  all  |
^  Engine (induction)  ^^^^^^
|  fuel pressure regulator  |  M6  |  1.0  |  12mm  |  bolt + split washer  |  all  |
|  pop-off valve port  |  1"  |  NPT  |    |    |  all  |
|  egr valve to intake  |  M8  |  1.25  |    |  stud + split washer + nut  |  all  |
|  throttle body to plenum  |  M8  |  1.25  |  40mm (10mm)  |  bolt + split washer  |  all  |
|  upper plenum to lower  |  M8  |  1.25  |  40mm (10mm)  |  bolt + split washer  |  all  |
|  injector retainer  |  M6  |  1.0  |  30mm (none)  |  bolt  |  all  |
^  Engine (exhaust)  ^^^^^^
|  exhaust manifold  |  M8  |  1.25  |    |  stud  |  84-87  |
|  exhaust manifold  |  M10  |  1.25  |  30mm  |  bolt  |  88-89  |
|  turbine to downpipe  |  M10  |  1.5  |    |  stud  |  all  |
|  downpipe to exhaust  |  M10  |  1.25  |    |  stud  |  all  |
|  egr manifold bung  |  M22  |  1.5  |    |    |  all  |
^  Transmission/Driveshaft  ^^^^^^
|  transmission mount to body  |  M10  |  1.5  |  20mm  |  bolt  |  all  |
|  transmission mount to isolator  |  M10  |  1.25  |  20mm (90mm)  |  bolt  |  all  |
|  driveshaft to differential  |  M10  |  1.25  |  30mm  |  bolt  |  all (turbo)  |
^  Front Suspension  ^^^^^^
|  tie rod end  |  M14  |  1.5  |    |  castle nut  |  all  |
|  steering rack to crossmember  |  M12  |  1.25  |  30mm  |  bolt  |  all  |
|  knuckle to strut  |  M12  |  1.25  |  40mm  |  bolt  |  all  |
|  caliper to strut  |  M12  |  1.25  |  40mm  |  bolt  |  all  |
|  tension rod bracket  |  M10  |  1.25  |  25mm  |  bolt  |  all  |
|  tension rod  studs  |  M10  |  1.5  |    |  nut  |  84-87  |
|  tension rod  studs  |  M12  |  1.5  |    |  nut  |  88-89  |
^  Rear Suspension  ^^^^^^
|  shock to lower mount  |  M12  |  1.25  |  ?  |  bolt  |  all  |
|    |  M12  |  1.25  |  40mm (80mm)  |  prev-torq nylock nuts  |  all  |
|  shock upper mount to body  |  M10  |  1.25  |  |  prev-torq nuts  |  all  |
|  differential cover  |  M8  |  1.25  |  25mm  |  bolt  |  all  |
|  differential mount to body  |  M10  |  1.5  |  60mm  |  bolt  |  all  |
|    |  M12  |  1.25  |    |  nut  |  all  |
|  differential mount to body  |  M10  |  1.5  |  60mm  |  bolt  |  all  |
|  differential to bracket  |  M14  |  1.5/2.0  |    |  stud  |  all  |
|    |  M14  |  1.5  |    |  nut  |  all  |
|  differential to crossmember  |  M12  |  1.25  |  25mm (150mm)  |  bolt  |  all  |
^  Body  ^^^^^^
|  front bumper cover  |  M6  |  1.0  |    |  prev-torq nuts  |  all  |
|  rear bumper cover  |  M5  |  1.0  |    |  prev-torq nuts  |  all  |
^  Interior  ^^^^^^
|  seat bracket  |  M10  |  1.5  |  25mm  |  bolt  |  all  |
^  Miscellaneous  ^^^^^^
|  acorn nut  |  M12  |  1.25  |    |  60° taper  |  84-86  |
|  lug nut  |  M12  |  1.25  |    |  60° taper  |  87-89  |